Tuesday, 1 November 2016

Andrea Miniatures' 'Technocop 2030'

Technocop 2030Trawling the Historex site is something of a voyeuristic experience for a figure maker and painter like yours truly. There are hundreds of different figures in a variety of scales produced by dozens of different makers, all of which makes choosing the next figure to buy and paint something of a daunting prospect. One of the classiest figure makers is Andrea Miniatures who offer a wide range of white metal kits from 54mm upwards and I had been thinking of tackling one of their kits for some time. I have my eye on a couple of their 75mm historical figures that will make nice future projects, but checking through their 54mm series I came across a number of figures quite obviously modelled after, or at least based on, figures from film and television ... and I was tempted in by these. This one labelled 'Technocop 2030' is obviously based on, the titular character from Paul Verhoeven's violent 1987 sci-fi classic Robocop. As to how closely the figure is modelled after its cinematic equivalent I've not bothered to find out, but it certainly ticks all the boxes from my uncritical standpoint and gave me one of the most pain-free builds I've tackled in a good while.

Counting the base, background and two little pistons that attach to the back of the legs, Technocop is a ten piece kit in white metal that comes in a well stuffed little box that carries numerous useful colour reference photos on the front and back. The parts were pretty cleanly moulded and for the most part required only a very basic tidy up with a craft knife and some fine wet and dry paper. There was a slight encrustation of metal on the right side on the back of the torso, but this was quite easily buffed back with my small engraving tool. The base exhibited a little more flash along the mould lines which needed trimming back, but again this was nothing to write home about and was quickly sorted out.
 
 
As to the build, it was simplicity itself, the figure went together without a hitch, bonded quickly with super glue, as too did the two-part stand. Mirroring a scene from the film, the figure is stepping through a large hole in a wall, his gun drawn, presumably intent on sorting out some nefarious malefactors on the other side. The wall here is set leaning backwards at a rather rakish angle, which gives the scene a slightly more interesting look and the figure is married into the correct position by a hole in the base into which a lug on the bottom of his right foot slots. All that is then required is to figure out just where to place Technocop's hand on the wall and you have your two glueing spots for later.

But first the painting. After undercoating I painted the entire base in Humbrol 32 dark grey acrylic and to give it a little more colour drybrushed the whole with Humbrol 93, followed by a lighter drybrushing around the large hole and on some of the surrounding rubble with Citadel Terminatus Stone. When dry the entire base was thoroughly coated in Army Painter Soft Tone to get a little contrast into the nooks and crannies. As the picture on the box had some graffiti painted on the wall I also used a few extra colours to make a few nondescript scribbles on the outer side (reasoning that the back of the stand was inside a building I left it graffiti-free). The edges if the stand and the wall were then painted black and after a coating of Army Painter Anti-Shine it was all put aside while I tackled the figure.
 
 
 
I undercoated the figure in dark grey enamel and the next day painted the black areas (lower torso, gloves, gun, elbows, eye slit and prosthetic jaw) with Humbrol 33 Matt Black and then painted what little of the face you can see in the same manner and with the same GW/Citadel colours referred to in earlier posts. Once painted the face had a noticeably pouty look to it as if he was fishing for a kiss. Before painting the armour I had to go shopping. In the film, our hero's armour has the distict look of blued metal, so I needed a metalic blue to mix with some of my silver acrylics. I had researched two - Humbrol 52 and Humbrol 222 - which I bought at the local model shop a day or so later. That evening I experimented and found that a 2-1 or 3-1 mix of Citadel Mithril Silver and Humbrol 222 gave me the colour I was after. So, when the next free daytime slot appeared I mixed up a puddle of paint on my paper palette and quickly coated all of the armour. This I then coated with Citadel Nuln Oil wash to pick out the lines and details before drybrucking more of the silver-metalic blue mix over it. Later I used raw Mithril Silver on some of the higher details to give them a bit of a lift and provide a highlight. This and a little drybrushing over the black areas with the Humbrol 32 I had used on the base, finished the figure off nicely.
 
Go on, give us a kiss.

Having buffed back to the metal where the foot and hand would be joined to the base, I stuck Technocop in place with super glue. It was then that I noticed a slight gap under the foot where it didn't fit flush to the base. This I filled with Plasto, but by this time I decided to add a little more rubble to the base as the few lumps that were moulded there seemed rather paltry remains for such a large hole. Rooting around in my supplies box I dug out a bag of small fish tank gravel and some coarse sand and sticking everything in place, first with super glue, then with thinned PVA, I let it all dry over night before painting it up in the same way that I had tackled the base to begin with.
 
 Technocop 2030


Technocop 2030 Technocop 2030
 

A fun build, easy, clean and trouble-free. Like the man said, 'I'd buy that for a dollar.'
 
 

No comments:

Post a Comment